Krux on M5StickV + Sparrow Wallet DIY Bitcoin Signer

In this guide, I’ll show you how to turn the M5StickV into a small Krux Bitcoin hardware signer and use it with Sparrow Wallet. The workflow is similar in spirit to SeedSigner: your signing device stays air-gapped, while a normal computer handles the wallet interface, address display, transaction creation, and broadcast.

Watch the video if you want to see the full setup on screen. This written version is meant to be useful even if you do not watch it.

M5StickV packaging showing the small touchscreen device
The M5StickV arrives in a small package with the compact device visible through the window.

Build your own hardware wallet

Kits, smartcard hats, cases and parts for SeedSigner, ShieldSigner, Specter DIY and Satochip builds, tested with the firmware shown in these videos and shipped from Canada.

What You Are Building

The M5StickV is a very small device, but for this setup it can run Krux as a stateless Bitcoin signer. That means you load your mnemonic into the device when needed, use it to verify addresses or sign transactions, and then shut it down. The seed does not need to stay loaded in memory between uses.

For this demo, I used:

  • M5StickV running Krux firmware
  • Sparrow Wallet as the coordinator wallet on a computer
  • A microSD card for moving PSBT files between the computer and the signer

The M5StickV is much smaller than many touchscreen signers, which makes it discreet. It also has physical buttons instead of touch controls, so menus take more patience to navigate.

Size comparison with other hardware wallets
The M5StickV is very small compared with larger hardware wallet devices.

1. Flash Krux Firmware to the M5StickV

First, connect the M5StockV to your computer using a USB-C cable. In the video, I used a standard USB-C cable for this step.

You will need the official Krux release files for the M5StickV target. The flashing process is similar to other Krux devices: you run the Krux tool and select the correct hardware target. In my case, that meant choosing the M5StickV option instead of another device.

Once the command is running, wait for the Krux logo to appear on the tiny screen. That tells you the firmware has loaded successfully.

Flashing Krux from the release folder
The Krux release folder contains the tools and device-specific folders used for flashing.

A few practical notes:

  • Use the official Krux release files, not random firmware from an unknown source.
  • Select the correct target for your hardware. In this case, that is M5StickV.
  • The device screen will be small, so make sure you can see it clearly while flashing and using menus.
Krux main menu on the M5StickV
After flashing, the M5StickV shows the Krux main menu.

2. Import Your Mnemonic by QR Code

Once Krux is running, you can import a mnemonic. In the video, I tested entering entropy manually using dice rolls and buttons. It works, but it is slow. For most people, importing a seed as a QR code is much faster and easier.

The M5StickV has a camera, so it can scan QR codes directly from another screen or printed material. That makes the workflow more practical than trying to enter every word using small physical buttons.

In my setup:

  1. Open Krux on the M5StickV.
  2. Choose the option to import a mnemonic.
  3. Select QR code scanning.
  4. Scan the seed QR code from another trusted screen or printed copy.
  5. Skip the passphrase if you do not want one for this demo wallet.
  6. Set the wallet as single-key for simplicity.
Krux dice-roll entry screen
Manual entropy entry is possible, but it takes a lot of button presses.

If you are using a passphrase, make sure you understand how to back it up and recover it properly. For this video, I skipped the passphrase to keep the example simple.

QR code seed import option
Importing by QR code is much faster than manual entry.

3. Import the Krux xpub into Sparrow Wallet

Now we need to connect the air-gapped signer to Sparrow Wallet on your computer. You do not give Sparrow access to your private keys. Instead, you import the extended public key, or xpub, from Krux.

On the M5StickV:

  1. Go to the option that displays the extended public key.
  2. View it as text if needed.
  3. Move to the QR code version of the xpub.

In Sparrow Wallet:

  1. Create a new wallet.
  2. Choose an air-gapped hardware wallet import path.
  3. Use the Specter DIY option, because Krux is not listed as its own separate choice in that menu.
  4. Scan the xpub QR code from the M5StickV screen.
  5. Apply the settings and finish creating the wallet.

This is where many people get stuck: Sparrow does not always list every possible air-gapped signer by name. The Specter DIY import path can work for compatible setups like this one.

Sparrow Wallet and M5StickV xpub QR code
The M5StickV displays the xpub as a QR code while Sparrow is ready to create the wallet.

4. Verify a Receive Address on the Device

Before sending Bitcoin to an address, you should verify that the address belongs to your wallet and signer. This is one of the main reasons to use a hardware signer: you can check important details on a device that has not been connected to the internet for signing operations.

In Sparrow Wallet:

  1. Go to Receive.
  2. Generate or display a receive address.
  3. Click the address so it appears large and clearly on your screen.

On the M5StickV:

  1. Choose Scan Address.
  2. Point the camera at the address shown in Sparrow.
  3. Confirm that the address is valid for your wallet.

This step helps protect you against a compromised computer showing you a wrong receive address. If the signer says the address belongs to your wallet, you have an extra layer of confidence before sending funds to it.

Sparrow receiving transaction
After verification and payment, the incoming Bitcoin appears in Sparrow.

5. Create a Multi-Output PSBT in Sparrow

For this demo, I created a transaction with multiple outputs. That lets us see how Krux handles external payments, internal wallet transfers, and change.

In my example:

  • One output went to an external tip address.
  • One output went to another address inside the same wallet.
  • Change was also generated by the wallet.

This is useful because it shows what you will actually see when signing on the M5StickV. You do not want surprises during a real transaction, especially if you are moving meaningful amounts of Bitcoin.

In Sparrow:

  1. Go to Send.
  2. Add your recipient address or addresses.
  3. Enter the amounts.
  4. Add descriptive names if that helps you review the transaction later.
  5. Create the transaction.
  6. Finalize it for signing.
  7. Save the unsigned PSBT file directly to a microSD card.
Multi-output transaction in Sparrow
Sparrow shows the multi-output transaction before it is saved as a PSBT.

A PSBT, or Partially Signed Bitcoin Transaction, is a file format that lets you prepare a transaction on one device and sign it on another. In this workflow, Sparrow prepares the unsigned transaction, Krux signs it, and Sparrow broadcasts the signed result.

6. Insert the microSD Card Correctly

The M5StickV has a microSD slot. For this setup, the card is used to move PSBT files between your computer and the signer.

When inserting the card:

  1. Make sure the card goes in with the text facing up.
  2. Push it in gently until you feel the standard spring mechanism engage.
  3. Do not force it if it does not fit easily; check orientation first.

One important limitation from the video: the official release shown does not support hot-swapping microSD cards while the device is running. That means if you insert a card after Krux has already started, you may need to shut down and restart the M5StickV before it recognizes the card properly.

Inserting microSD card
The microSD card goes into the M5StickV for PSBT file transfer.

7. Restart If Needed After Inserting the Card

In my test, after inserting the microSD card while Krux was running, the device did not behave as expected. So I shut it down and restarted it.

There was also a small power issue during testing: after shutting down, the device did not immediately turn back on. I left it plugged in to charge for a period of time before powering it up again. Once it powered on, the microSD card was accessible.

This is a practical reminder that small battery-powered devices can have quirks. If you are using this as part of your Bitcoin security setup, test the full workflow with small amounts first. Do not assume everything will work perfectly during your first real transaction.

M5StickV after restart
After charging and restarting, the device can be used again.

8. Load Your Mnemonic Again on the Signer

Because this is a stateless signer, you load your mnemonic when you need to use it. In my demo, I scanned the same seed QR code that I had used earlier.

On the M5StickV:

  1. Power on Krux.
  2. Choose Load Mnemonic.
  3. Scan the QR code for your seed.
  4. Confirm the wallet type and settings as needed.

This step is where manual button entry becomes painful. If you are using a stateless device regularly, storing your seed as a QR code makes life much easier. That said, if this device is only used occasionally as part of backup or multisig recovery, less frequent seed loading may be acceptable.

Load Mnemonic menu
The signer loads the mnemonic before signing.

9. Sign the PSBT from microSD

With the mnemonic loaded and the microSD card inserted, you can sign the unsigned transaction.

In Krux:

  1. Choose the option to sign a transaction from a PSBT file.
  2. Confirm the warning that some checks may not be available because the file was not fully loaded through the normal interactive flow. For single-signature use in this demo, I proceeded.
  3. Select the PSBT file found on the microSD card.
  4. Review the transaction details shown by Krux.

This is where the multi-output example becomes useful. In my test transaction, only the external output was displayed clearly as an outgoing payment to a non-wallet address. The internal wallet transfer and change were not shown in the same way on that signing screen.

That behavior matters. When reviewing transactions, pay close attention to what Krux shows you and make sure it matches what you intended to send. If something looks unexpected, stop and investigate before signing.

Signing confirmation
Krux shows the sending details before the transaction is signed.

After confirming:

  1. Choose Sign.
  2. Confirm again when prompted.
  3. Save the signed PSBT back to the microSD card.
  4. Remove the card and insert it into your computer.

10. Broadcast the Signed Transaction in Sparrow

Now that you have a signed PSBT file, you can return to Sparrow Wallet.

In Sparrow:

  1. Load the transaction from the microSD card.
  2. Select the signed PSBT file.
  3. Confirm the details look correct.
  4. Broadcast the transaction.

Once broadcast, the transaction is sent to the Bitcoin network and will wait for confirmations like any other Bitcoin transfer.

Sparrow ready to broadcast
The signed transaction can be loaded back into Sparrow and broadcast.

What This Setup Is Good For

This M5StickV + Krux + Sparrow setup is useful if you want a compact, stateless signer that works with a familiar desktop wallet. It gives you:

  • A small physical device for signing
  • Address verification on the signer screen
  • PSBT-based transaction review and signing
  • Air-gapped signing workflow using microSD
  • Compatibility with common Bitcoin wallet concepts like xpubs, receive addresses, change, and external outputs

It is not a magic security solution. The same DIY hardware caveats apply as they do for other air-gapped signers: you are responsible for firmware source, physical access, seed backup, transaction review, and safe handling of the device. If someone can physically tamper with your signer or steal your seed material, no software workflow fully fixes that problem.

Practical Security Notes

Before using this setup for real funds, I would recommend testing it carefully:

  • Flash firmware from official release files only.
  • Verify the process on a test wallet first.
  • Use QR code import where possible to reduce manual entry errors.
  • Always verify receive addresses on the signer before sending meaningful amounts.
  • Review PSBT outputs carefully, especially when using multi-output transactions.
  • Understand that internal transfers and change may not appear the same way as external payments in Krux’s signing view.
  • Test microSD insertion, restart behavior, and battery power with small test transactions.
  • Keep your seed backup safe and know how to restore it before you need it under pressure.

Conclusion

The M5StickV is a very small option for running Krux as a Bitcoin hardware signer. It may not be the fastest device to use because of its tiny screen and physical buttons, but it has real value if you want something compact, discreet, and capable of air-gapped signing with Sparrow Wallet.

For many people, the best workflow is to keep your seed available as a QR code for faster loading, verify addresses on the signer, sign PSBT files from microSD, and broadcast only after reviewing everything carefully. Done that way, this setup gives you a practical DIY Bitcoin hardware wallet experience in a surprisingly small package.

Questions from viewers

Common questions from the comments on this video, with my answers.

Can I use an M5StickC or TTGO board instead of the M5StickV?

No, you cannot. The Krux firmware runs on platforms using the Kendryte K210 chip, whereas the M5StickC and TTGO boards are ESP32 platforms. They are not compatible.

Is it possible to recover a wallet if I only have 8 out of my 12 seed words?

It is not practical for most people right now. Brute-forcing the missing four words requires massive computing power, which is currently only feasible for very large wallets (over $1 million). For smaller amounts, your best bet is to keep the information safe and try again in about 10 years when computing power has increased significantly. (Apps and tools change, so check the current version if something looks different.)

I am getting errors like 'python not found' or 'No module named Crypto' when trying to run recovery tools. What should I do?

These errors usually happen because the necessary software dependencies aren't installed correctly. You need to follow the specific installation guides for tools like BTCRecover carefully to ensure all required modules are present before running the commands.

Should I consider the OneKey hardware wallet as an alternative?

It is essentially a clone of the Trezor. If you are looking for that type of device, it is better to just get a genuine Trezor directly.

Build your own hardware wallet

Kits, smartcard hats, cases and parts for SeedSigner, ShieldSigner, Specter DIY and Satochip builds, tested with the firmware shown in these videos and shipped from Canada.

Found this useful?

These guides are free and ad-free. You can support them by sharing them, subscribing on YouTube, or sending a tip.

Stuck on this?

Book a one-hour session and I’ll walk you through it, or ask about a trusted recovery.

Recovery guides

More guides