Ellipal Titan Mini Teardown: Components & Security

In this teardown of the Ellipal Titan Mini, I cut the device open to see what is actually inside. The goal was simple: give you a practical, written look at the hardware architecture and compare it with the original Ellipal Titan. You can also watch the video if you want to see the full process.

This is not a repair guide. It is a destructive teardown of a sacrificial device, done because Ellipal does not publish enough detail for me to fully verify its security model from the outside alone. If you are deciding whether the Titan Mini is a meaningful upgrade over the original Titan, this article should help you understand what changed and what still requires trust in Ellipal’s closed-source firmware.

Why I Cut Open an Ellipal Titan Mini

The Ellipal Titan Mini was already interesting to me because it looked smaller than the original Titan, but not simply like a shrunken version of the same device. During my earlier testing, I ended up bricking two units while trying different things. Once that happened, one of them became a good candidate for teardown.

The main questions were:

  1. Is the Mini still running full Android?
  2. Does it use a dedicated secure element?
  3. What is the main processor?
  4. How does the physical build compare with the original Titan?
  5. Does this change how I view its security model?

Those are important questions because hardware wallets are not just “a phone that stores keys.” The operating system, chip choices, firmware, and secure element all matter. A device can look simple on the outside while running a much larger software stack internally, or it can use a more focused embedded design with a smaller attack surface.

Cutting the Device Open Safely

The Titan Mini contains a lithium battery, so cutting into it indoors in an enclosed space would have been a bad idea. I moved outdoors, used safety goggles and a face visor, and clamped the device in a Dremel mini-vise mounted on a bench clamp.

Ellipal Titan Mini clamped in a Dremel vise ready for teardown
The Ellipal Titan Mini is clamped flat and ready to be cut open.

I did not try to remove the case cleanly. The device is built with glued parts and a metal frame, so a full non-destructive disassembly would have been difficult at best. Instead, I cut around the edge of the casing to expose the internal board. During this process, I pierced the battery, which is another reason this teardown was done outdoors with proper safety gear.

Once the outer metal had been trimmed enough, I removed the damaged battery and set it aside. That made the remaining work safer and easier. The main PCB could then be unscrewed from the chassis and examined more closely.

Opened Ellipal Titan Mini showing PCB, camera module, and internal layout
Top-down view of the opened device with the green PCB and battery area exposed.

Main Processor: Allwinner V831 SoC

The most important finding was the main processor. After removing the RF shield from the main board, I identified an Allwinner V831 system-on-chip. This is a full HD camera-focused SoC, not a general-purpose smartphone-class Android processor in the way the original Titan was often described.

Main PCB with Allwinner V831 SoC and Winbond flash memory exposed
The RF shield has been removed, revealing the main SoC and flash chip.

This matters because it strongly suggests that the Ellipal Titan Mini is running custom firmware rather than a full Android operating system. In plain English: it behaves more like a traditional embedded hardware wallet, similar in concept to devices such as Trezor or Ledger, rather than a locked-down Android phone with a crypto app on top.

That does not automatically make it perfect. Closed-source firmware can still contain bugs, weak key handling, poor update security, or other issues that cannot be fully verified without source code and independent review. But from an attack-surface perspective, running a focused custom firmware image is generally better than running full Android, because there is less operating-system complexity to exploit.

This was one of the clearest differences between the original Titan and the Mini. The original Titan’s architecture was much closer to a smartphone platform. The Mini appears to be a more purpose-built embedded device.

Flash Memory: Winbond Chip

Next to the Allwinner V831, I found a Winbond flash memory chip on the main board. This is likely used for storing device data and firmware-related contents.

I did not desolder it or attempt to read its contents in this teardown. That would be a deeper forensic step, and because the device was already being cut open, I avoided damaging it further unless needed. If someone wants to go further, extracting and analyzing that flash chip could reveal more about how the firmware is stored, updated, and protected.

One practical note: if you are ever doing this kind of work on a device you care about, cutting or prying at chips is not the right way to inspect them. Desoldering with proper equipment is much safer for recovering data. In this case, the unit was sacrificial, so I only needed enough visual information to identify the components.

Touchscreen Controller and Secondary MCU

On the front-side flex area, I identified a touchscreen controller marked as an FT6336DMB / GRJ4401B part. This is not security-critical in itself; it simply handles touch input from the display.

I also found a secondary microcontroller on the board. It appeared to be a basic NationTech MCU, used for simpler functions rather than cryptographic operations. From what I could see, this chip does not appear to be the main place where private keys would be protected. Its role is more likely related to low-level device control, input handling, or other non-security-critical tasks.

This distinction matters. A small basic MCU can help with everyday functions, but it should not be confused with a secure element. The security of your keys depends on the chip actually responsible for key storage and signing operations.

Secure Element: The Big Upgrade

The most significant security-related finding was a separate security IC on the board. Based on the markings and available references, this appears to be a certified secure IC with an EAL 5+ rating.

Close-up of the PCB area identified as containing the secure element
The screwdriver points to the small chip identified as the secure element.

I am not going to overstate what that certification proves by itself. An EAL rating tells you something about how the product was evaluated, but it does not tell you everything about Ellipal’s actual implementation, firmware logic, update process, or key handling. Still, the presence of a dedicated secure element is meaningful.

In practical terms, this suggests that the Titan Mini uses specialized hardware for cryptographic key storage and operations, rather than relying only on the main SoC to protect keys inside software. That is similar in concept to secure elements found in other hardware wallets such as Ledger, Keystone, Coldcard, or BitBox devices.

This is a major step up from the original Ellipal Titan, which was essentially built around an Android-style phone platform. Even if modern phones can use trusted execution environments and other protections, having a separate dedicated chip for wallet security is still a stronger design choice for this specific job.

Physical Build: Metal Frame, Glue, and Charging Contacts

The physical construction also explains why the device feels so solid. The Titan Mini uses a metal frame, with the front plastic/display assembly glued into place. There is a fairly thick frame around the edge, and the internal layout is shaped to fit tightly inside the chassis.

I cut away part of the front plastic insert to see where the screen ended and the metal began. Once that was done, I could remove more of the front assembly and inspect the frame.

Detached front panel showing display and metal bezel edge
The detached front panel shows the display and freshly cut metal bezel.

The charging system uses four spring-loaded magnetic contacts on the edge of the device, which connect to pads on the board. This is a neat design because it avoids an open USB port that could be used for data access or physical tampering. The power button also pops out from the frame during disassembly.

From a durability perspective, this explains why Ellipal can show off the device surviving rough handling. It is not just marketing fluff; the internal metal structure and glued assembly make it physically resistant to casual damage. That said, physical ruggedness does not replace cryptographic security. A wallet can survive being dropped or crushed and still be vulnerable if its firmware or key management is weak.

Disassembled components laid out: display module, PCB, and metal frame
The removed display module, main PCB, and metal frame are shown after teardown.

Comparison With the Original Ellipal Titan

Based on this teardown, I would not describe the Titan Mini as “just a smaller Titan.” It is a fundamentally different architecture.

Here is how I see it:

Area Original Ellipal Titan Ellipal Titan Mini
Main platform Android-style phone-like system Embedded SoC with custom firmware
Software attack surface Larger due to full OS complexity Smaller because of focused firmware
Secure element Not a dedicated wallet-specific secure element in the same way Appears to include a certified security IC
Physical build Durable, but based on older architecture Metal frame, glued front assembly, spring contacts
User experience Guided Ellipal workflow Similar guided workflow, with app lock-in concerns

The biggest takeaway is that the Mini is a much more modern hardware wallet design. It moves away from the “smartphone” model and closer to the kind of architecture you expect from serious air-gapped or embedded hardware wallets.

That said, I was surprised Ellipal did not make a bigger deal of this. The security improvements are significant enough that they should be central to how the product is marketed. Of course, there is a business challenge: promoting a new device as more secure can make the older model look worse by comparison. But from a user’s perspective, knowing that the Mini uses custom firmware and a dedicated secure element is important information.

What Still Requires Trust in Ellipal

The hardware improvements do not solve every security question. The biggest remaining caveat is that Ellipal’s firmware remains closed source.

That means you can inspect chips, identify components, and see the general architecture, but you still cannot independently audit all of the security-critical code unless Ellipal publishes it or allows independent review to happen in a meaningful way. For some users, that will be acceptable. They may choose to trust Ellipal as a company and rely on the device’s guided workflow.

For more advanced users, closed-source firmware can be a deal breaker. If you want full transparency over how keys are generated, stored, signed, updated, and protected, closed source limits your ability to verify that yourself.

There is also the app ecosystem issue. Ellipal tends to lock you into its own wallet software. That can be good for beginners because it reduces the chance of making a mistake. But it can be limiting if:

  1. You need support for many different Ethereum chains beyond what Ellipal supports.
  2. You want to use third-party tools more freely.
  3. You are relying on advanced workflows that require broader compatibility.
  4. You want less dependence on one vendor’s software stack.

For that reason, the Titan Mini may be a better fit for users who value simplicity and guided security over maximum flexibility. Advanced users should think carefully about whether they are comfortable with Ellipal’s ecosystem limitations.

Who Is This Device For?

The Ellipal Titan Mini seems best suited to people who want:

  • A simpler, more guided hardware wallet experience.
  • An air-gapped QR-code-based workflow.
  • A device that is physically robust and easy to carry.
  • Stronger internal hardware than the original Titan.
  • Less complexity when generating keys or signing transactions.

It may be less ideal for users who want:

  • Full open-source firmware transparency.
  • Broad third-party app support.
  • Maximum flexibility across many chains.
  • The ability to independently audit every part of the key management process.

One area where Ellipal still stands out is sweeping funds from older paper wallets or legacy setups. If that is your main use case, the Titan Mini may be especially useful because it can make that process more structured and less error-prone than doing it manually on a computer.

Final Thoughts

This teardown confirmed what I suspected: the Ellipal Titan Mini is not just a smaller version of the original Titan. It uses a different internal architecture, with an Allwinner V831 SoC running custom firmware rather than full Android, and it appears to include a dedicated certified secure element for key-related operations.

Those are meaningful security improvements. The device has a smaller software attack surface and more specialized hardware protection than the original Titan. The physical build is also solid, with a metal frame, glued front assembly, and spring-loaded magnetic charging contacts that contribute to durability.

But the closed-source firmware remains an important limitation. You can see the chips, but you still cannot fully verify all of the security-critical code without independent access or published source. For many users, that trade-off may be acceptable. For advanced users who want maximum transparency and flexibility, it may not be enough.

If you are comparing the Titan Mini with other hardware wallets, I would focus on three things: whether you trust Ellipal’s closed-source model, whether its supported chains and workflow fit your needs, and whether the guided experience is worth the reduced flexibility. From a hardware standpoint, this teardown shows that the Mini has moved in a much more security-minded direction than the original Titan.

Choosing a hardware wallet?

See how this device stacks up against the others I’ve tested: security model, supported coins, backup options and price.

Some links on this site are affiliate links: if you buy through them I may earn a commission at no extra cost to you. It doesn’t change what I recommend.

Found this useful?

These guides are free and ad-free. You can support them by sharing them, subscribing on YouTube, or sending a tip.

Stuck on this?

Book a one-hour session and I’ll walk you through it, or ask about a trusted recovery.

Recovery guides

More guides