SeedKeeper V2 Review: Secure Hardware Password Manager

The SeedKeeper from Satochip is a useful offline or semi-offline way to store things that matter in crypto life: seed phrases, passphrases, wallet descriptors, and high-value passwords. The idea is simple but powerful — put sensitive data onto a small smartcard you can physically carry, store in multiple places, or hand to someone under controlled conditions, without leaving it sitting in a cloud password manager or on an always-connected device.

In this written version of the video, I walk through the updated SeedKeeper V2 cards and the new SeedKeeper mobile app. You can also watch the video if you want to see the demos in motion.

What changed with SeedKeeper V2?

The main practical improvements I care about are:

  • Longer passwords than were possible on older SeedKeeper cards.
  • Deletion of secrets, which was not available before. This matters a lot when using the card as a general password manager.
  • A much better mobile app experience for adding, viewing, deleting, and exporting secrets.
  • Backup cloning that does not overwrite existing data on the target card.
  • Unique PINs per cloned card, which is useful for inheritance or distributed storage.
  • DIY JavaCard support, including flashing V2 firmware to compatible cards through an updated SeedSigner fork.

The total storage on the card is still around 4 KB, so this is not a device for storing large documents. It is aimed at high-value secrets: recovery phrases, wallet descriptors, passphrases, and a handful of important passwords you want kept extra secure.

SeedKeeper V2 card with tamper-evidence sticker next to Satochip packaging
The SeedKeeper arrives as a smartcard with a tamper-evidence sticker.

Unpacking the SeedKeeper V2

The retail card is straightforward: you get the SeedKeeper card, a brochure, and a tamper-evidence sticker. The artwork has not changed much from earlier cards, so if you have older cards, it can be easy to mix them up. I label mine by version so I know which one is which.

That physical simplicity is part of why these cards work well for storage. A smartcard is small, durable enough for normal handling, and easy to keep in a wallet, safe, document folder, or with a trusted person. The tamper-evidence sticker also gives you a basic visual cue if someone has tried to open the package.

Installing and setting up the mobile app

The new SeedKeeper mobile app is the easiest way to use these cards now. It makes setup, secret management, backups, PIN changes, logs, and factory reset much more approachable than older desktop-only workflows.

Initial card setup steps

  1. Install the SeedKeeper app on your phone.
  2. Open the app and start the setup flow.
  3. Enter a PIN twice to initialize the card.
  4. Scan the new SeedKeeper card against the phone’s NFC reader.
  5. Log in with the PIN you just set.

The first time I tried scanning an uninitialized card, it told me the card was not initialized yet. That is expected. You need to configure the PIN before the app can use the card properly.

SeedKeeper mobile app showing the setup new PIN screen
Set a PIN during first-time card initialization.

From there, the app shows that the card has no secrets on it yet. That is your clean starting point.

Types of secrets you can store

The SeedKeeper is useful for more than just passwords. In the app, when adding a secret, you can work with:

  • Passwords
  • Mnemonics, such as wallet recovery phrases
  • Wallet descriptors, which are especially important if you use multi-sig setups
  • Random data or notes that you want to keep offline

This makes the card more flexible than a single-purpose seed phrase holder. You can treat it like a small, physical vault for sensitive items that do not need constant access but should be protected from casual device compromise.

One important security note: if you generate mnemonics in the app on your phone, those mnemonics are created on the phone. Unless that phone is truly offline and air-gapped, treat generated mnemonics as hot material. For maximum security, import pre-generated or independently secured secrets rather than relying on a connected phone to create them.

Saving a password to the card

To store a password:

  1. Open the SeedKeeper app.
  2. Choose Add secret.
  3. Select Import if you already have the secret.
  4. Enter a label, username or URL context, and the password itself.
  5. Confirm the import.
  6. Scan the card against your phone to write it securely.

In the demo, I stored a simple labeled password entry. The important part is not the specific password — it is that the secret now lives on the card, protected by the card PIN and the app workflow.

SeedKeeper app Add secret menu with Generate and Import options
You can generate a new secret or import an existing one.

When you open the entry again, you can reveal it after scanning the card. The app also lets you copy the secret or display it as a QR code. That QR option is handy if you want to transfer the secret to another device without typing it in manually.

Password detail screen showing QR export and delete options
Secrets can be revealed, exported as QR codes, or deleted.

The deletion feature is a big quality-of-life improvement. Older cards could store secrets, but you could not remove them through the same workflow. If a password changes, becomes obsolete, or was stored by mistake, being able to delete it makes the card much more practical for ongoing use.

Generating strong passwords

The app can also generate new secrets for you. For passwords, you get common options such as length and character sets. You can move from shorter passwords up to longer ones, or switch into passphrase-style output when you want something easier to remember but still strong.

To generate a password:

  1. Choose Generate secret.
  2. Select the password option.
  3. Adjust the strength settings you want.
  4. Add at least a label.
  5. Generate until you are happy with the result.
  6. Import it onto the card by scanning the card.

This is useful for creating new high-value passwords that never need to exist in your normal password manager, browser history, or cloud sync. You can keep only the most sensitive credentials on the SeedKeeper and leave everyday passwords elsewhere.

Card information, logs, and settings

The app also exposes card-level details and maintenance options through the menu.

You can view:

  • Card version
  • Available storage
  • Whether a retail card is shown as genuine
  • A label you assign to the card
  • PIN change options
  • Activity logs

The logs are useful if you want an audit trail of actions on the card, such as imports, exports, and resets. If you are using these cards for inheritance or distributed storage, that kind of history can be helpful when verifying that a card has been used as expected.

You can also adjust settings such as tutorial behavior and debug mode. The same area is where factory reset lives if you need to wipe the card.

Cloning backup cards with unique PINs

One of the most useful SeedKeeper features is cloning secrets from one card to another. This is especially valuable for inheritance or distributed storage because each cloned card can have its own PIN.

That means you could give different people different cards, store them in different locations, and ensure that possession of the card alone is not enough to access the secrets. The person would also need the specific PIN assigned to that copy.

Backup cloning steps

  1. Open the app on your phone.
  2. Scan the master card you want to back up.
  3. Enter the PIN for that card.
  4. Choose Make a backup.
  5. Start with the backup card and enter its PIN.
  6. Scan the master card again so the app can create an encrypted backup of its contents.
  7. Confirm the backup.
  8. Scan the target card to complete the transfer.
SeedKeeper backup screen showing master card to backup card flow
Backup copies missing secrets from one card to another.

A key detail: backup does not overwrite what is already on the destination card. It adds secrets that are missing from the target card. That makes it safer to use repeatedly and more flexible for combining different subsets of secrets across multiple cards.

For example, you might have several cards with overlapping or separate secrets. You can clone them into another backup card without accidentally destroying existing data on that card. For inheritance planning, this is a very nice property. It lets you create redundant copies while still keeping access control through separate PINs.

Factory reset demo

If you forget the PIN or want to return a card to a clean state, the app can factory reset it. The process requires repeating the reset command several times in sequence: send reset command, scan the card, repeat until the card is wiped.

This deliberate friction is a good thing. You do not want to accidentally wipe a card full of important secrets with one careless tap. The repeated confirmation makes the action intentional.

After the reset, the card returns to an uninitialized state and can be set up again with a new PIN.

DIY SeedKeeper JavaCards

If you like building your own hardware, the DIY path is where SeedKeeper gets even more interesting. You can flash compatible JavaCards with SeedKeeper V2 firmware using an updated SeedSigner fork. This means you are not limited to retail cards if you want to experiment or create additional copies.

For standard DIY JavaCards, the process is:

  1. Use the updated SeedSigner fork that supports SeedKeeper functions.
  2. Insert a compatible blank JavaCard into the card reader.
  3. Open the smartcard tools area on the device.
  4. Select the SeedKeeper V2 applet installation option.
  5. Flash the applet to the card.
  6. Use the mobile app or desktop utility to initialize and manage the new card.

If you are using a THD-89 based NFC micro tag, there is an extra step: build the required applets on-device from source before flashing them onto the tag. The end result can give you much of the functionality of a full-sized SeedKeeper in a smaller, more discreet form factor — something that could fit on a keychain or stay hidden in a compact location.

DIY SeedSigner-style device with card slot and SeedKeeper V2 card
A DIY smartcard reader setup can be used to manage SeedKeeper cards.

The app works the same way with DIY cards, with one expected difference: in card information, DIY cards are not shown as genuine. That is normal because they were not issued through the retail channel. The functionality still works if the card has been flashed correctly.

If you want to try the DIY route, compatible JavaCards can be purchased from Satochip or from my store. I sell a J3H145 Javacard that is useful for this kind of project. These cards are cheap to ship and easy to replace if you make a mistake during testing, which is another reason I like keeping spares around when working with smartcards.

SeedSigner plus SeedKeeper

The SeedKeeper also pairs well with SeedSigner-style devices. In the updated fork, you can not only load seeds from the card, but also use smartcard tools to view secrets, display them as QR codes, save passwords, and delete secrets from the card.

That makes the combination useful in a few ways:

  • Use the SeedKeeper as an offline seed storage device.
  • Load selected seeds into an air-gapped signing workflow.
  • Manage high-value passwords without exposing them to normal devices.
  • Keep backup copies on multiple cards with separate PINs.

The updated fork also supports installing other applets onto DIY cards, including SmartPGP, SpecterDIY, and VivoKey OTP for TOTP-style use cases. That turns a blank JavaCard into a small multi-purpose secure element rather than just a single-function seed holder.

Select Applet menu showing available smartcard applets
The updated tooling can install multiple useful applets onto compatible cards.

Upcoming smartcard hat direction

One of the annoying parts of DIY smartcard projects is reader reliability. Some cheap PN532-based boards work fine, but many clones are inconsistent and frustrating to deal with. In the video, I show a more reliable approach using a full smart card reader wired into the Raspberry Pi GPIO pins instead of relying on USB.

The longer-term goal is to package that kind of connection as a proper hat that can stack between the screen and the Raspberry Pi board, or attach in another way depending on how you want to build your device. If you are interested in this direction, keep an eye out for updates. You can also see the related Smartcard Hat for Raspberry Pi with USB-C Input power in my store as a useful reference point for hardware that is moving toward more reliable smartcard integration.

SatoChip Utils desktop option

If you prefer working on a desktop PC rather than a phone, there is also a utility called SatoChip Utils. It brings together functionality for different Satochip cards and lets you do many of the same card management tasks from a desktop environment.

This is useful if you are:

  • Managing multiple cards
  • Testing DIY builds
  • Working in an environment where you prefer a keyboard and physical reader over NFC on a phone
  • Building a repeatable workflow for backups or applet installation

The mobile app is the easiest day-to-day option, but having a desktop utility gives you another path if your setup calls for it.

My take: who should use SeedKeeper?

I think SeedKeeper is especially useful for crypto users who want an extra layer of physical separation for high-value secrets. It is not trying to replace a full password manager with hundreds of entries. Instead, it works well for the smaller set of credentials and recovery materials you want protected from ordinary device compromise.

It shines in these use cases:

  • Storing seed phrases offline or semi-offline
  • Keeping wallet descriptors safe for multi-sig setups
  • Protecting passphrases that unlock larger value
  • Managing a handful of high-value passwords separately from normal password managers
  • Creating inheritance copies with unique PINs
  • Building DIY smartcard backups on JavaCards

The biggest improvement since earlier versions is the user experience. The old workflow was more clunky, and some features were missing or awkward to use. With V2 cards, the mobile app, deletion support, better storage for longer passwords, and cleaner backup behavior, these cards are much easier to recommend for practical security work.

If you are comfortable with smartcards and want a small, portable, PIN-protected way to store sensitive crypto material, SeedKeeper is worth looking into. And if you like DIY hardware, the open-source ecosystem around it gives you a lot of room to build exactly what you need.

Choosing a hardware wallet?

See how this device stacks up against the others I’ve tested: security model, supported coins, backup options and price.

Some links on this site are affiliate links: if you buy through them I may earn a commission at no extra cost to you. It doesn’t change what I recommend.

Found this useful?

These guides are free and ad-free. You can support them by sharing them, subscribing on YouTube, or sending a tip.

Stuck on this?

Book a one-hour session and I’ll walk you through it, or ask about a trusted recovery.

Recovery guides

More guides